Open CASCADE Technology  6.7.0

Building 3rd-party libraries on Linux

Introduction

This document presents additional guidelines for building third-party products used by Open CASCADE Technology and samples on Linux platform.

The links for downloading the third-party products are available on the web site of OPEN CASCADE SAS at http://www.opencascade.org/getocc/require/.

There are two types of third-party products, which are necessary to build OCCT:

  • Mandatory products: Tcl/Tk 8.5 - 8.6 and  FreeType 2.4.10 - 2.4.11
  • Optional products: TBB 3.x - 4.x, gl2ps 1.3.5 - 1.3.8, FreeImage 3.14.1 - 3.15.4

Building Mandatory Third-party Products

Tcl/Tk

Tcl/Tk is required for DRAW test harness.

Installation from binaries:

It is possible to download ready-to-install binaries from http://www.activestate.com/activetcl/downloads

  1. Download the binaries archive and unpack them to some TCL_SRC_DIR.
  2. Enter the directory TCL_SRC_DIR.
    cd TCL_SRC_DIR
    
  3. Run the install command

    install.sh
    

    and follow instructions.

Installation from sources: Tcl

Download the necessary archive from http://www.tcl.tk/software/tcltk/download.html and unpack it.

  1. Enter the unix sub-directory of the directory where the source files of Tcl are located (TCL_SRC_DIR).
    cd TCL_SRC_DIR/unix   
    
  2. Run the configure command

    configure --enable-gcc  --enable-shared --enable-threads --prefix=TCL_INSTALL_DIR   
    

    For a 64 bit platform also add –enable-64bit option to the command line.

  3. If the configure command has finished successfully, start the building process
    make   
    
  4. If building is finished successfully, start the installation of Tcl. All binary and service files of the product will be copied to the directory defined by TCL_INSTALL_DIR
    make install   
    

Installation from sources: Tk

Download the necessary archive from http://www.tcl.tk/software/tcltk/download.html and unpack it.

  1. Enter the unix sub-directory of the directory where the source files of Tk are located (TK_SRC_DIR).
    cd TK_SRC_DIR/unix   
    
  2. Run the configure command, where TCL_LIB_DIR is TCL_INSTALL_DIR/lib

    configure --enable-gcc  --enable-shared --enable-threads --with-tcl=TCL_LIB_DIR  --prefix=TK_INSTALL_DIR   
    

    where TCL_LIB_DIR is TCL_INSTALL_DIR/lib

    For a 64 bit platform also add –enable-64bit option to the command line.

  3. If the configure command has finished successfully, start the building process
    make   
    
  4. If building has finished successfully, start the installation of Tk. All binary and service files of the product will be copied to the directory defined by TK_INSTALL_DIR (usually TK_INSTALL_DIR is TCL_INSTALL_DIR)
    make install   
    

FreeType

FreeType is required for display of text in 3D viewer. Download the necessary archive from http://sourceforge.net/projects/freetype/files/ and unpack it.

  1. Enter the directory where the source files of FreeType are located (FREETYPE_SRC_DIR).
    cd FREETYPE_SRC_DIR   
    
  2. Run the configure command

    configure  --prefix=FREETYPE_INSTALL_DIR   
    

    For a 64 bit platform also add CFLAGS='-m64 -fPIC' CPPFLAGS='-m64 -fPIC' option to the command line.

  3. If the configure command has finished successfully, start the building process
    make   
    
  4. If building has finished successfully, start the installation of FreeType. All binary and service files of the product will be copied to the directory defined by FREETYPE_INSTALL_DIR
    make install   
    

Building Optional Third-party Products

TBB

This third-party product is installed with binaries from the archive that can be downloaded from http://threadingbuildingblocks.org. Go to "Downloads page", find the release version you need and pick the archive for Linux platform. To install, unpack the downloaded archive of TBB product.

gl2ps

Download the necessary archive from http://geuz.org/gl2ps/ and unpack it.

  1. Install or build cmake product from source file.
  2. Start cmake in GUI mode with the directory where the source files of gl2ps are located:

    ccmake GL2PS_SRC_DIR   
    

    a. Press [c] to make the initial configuration b. Define the necessary options CMAKE_INSTALL_PREFIX c. Press [c] to make the final configuration d. Press [g] to generate Makefile and exit

    or just run the following command:

    cmake  –DCMAKE_INSTALL_PREFIX=GL2PS_INSTALL_DIR –DCMAKE_BUILD_TYPE=Release   
    
  3. Start building of gl2ps
    make   
    
  4. Start the installation of gl2ps. Binaries will be installed according to the CMAKE_INSTALL_PREFIX option
    make install   
    

FreeImage

Download the necessary archive from http://sourceforge.net/projects/freeimage/files/Source%20Distribution/ and unpack it. The directory with unpacked sources is further referred to as FREEIMAGE_SRC_DIR.

  1. Modify FREEIMAGE_SRC_DIR/Source/OpenEXR/Imath/ImathMatrix.h: In line 60 insert the following:
    #include string.h   
    
  2. Enter the directory where the source files of FreeImage are located (FREEIMAGE_SRC_DIR).
    cd FREEIMAGE_SRC_DIR   
    
  3. Run the building process
    make   
    
  4. Run the installation process

    a. If you have permissions to write to /usr/include and /usr/lib directories then run the following command:

       make install   
    

    b. If you don’t have permissions to write to /usr/include and /usr/lib directories then you need to modify the file FREEIMAGE_SRC_DIR/Makefile.gnu:

    Change lines 7-9 from:

    DESTDIR ?= /   
    INCDIR  ?= $(DESTDIR)/usr/include   
    INSTALLDIR  ?= $(DESTDIR)/usr/lib   
    

    to:

    DESTDIR  ?= $(DESTDIR)   
    INCDIR  ?= $(DESTDIR)/include   
    INSTALLDIR  ?= $(DESTDIR)/lib   
    

    Change lines 65-67 from:

    install  -m 644 -o root -g root $(HEADER) $(INCDIR)   
    install  -m 644 -o root -g root $(STATICLIB) $(INSTALLDIR)   
    install  -m 755 -o root -g root $(SHAREDLIB) $(INSTALLDIR)   
    

    to:

    install  -m 755 $(HEADER) $(INCDIR)   
    install  -m 755 $(STATICLIB) $(INSTALLDIR)   
    install  -m 755 $(SHAREDLIB) $(INSTALLDIR)
    

    Change line 70 from: 

    ldconfig
    

    to:

    \#ldconfig   
    

    Then run the installation process by the following command:

     make DESTDIR=FREEIMAGE_INSTALL_DIR  install   
    
  5. Clean the temporary files
     make clean   
    

OpenCL ICD Loader

If you have OpenCL SDK (one provided by Apple, AMD, NVIDIA, Intel, or other vendor) installed on your system, you should find OpenCL headers and libraries required for building OCCT inside that SDK.

Alternatively, you can use OpenCL ICD (Installable Client Driver) Loader provided by Khronos group. The following describes steps used to build OpenCL ICD Loader version 1.2.11.0.

  1. Download OpenCL ICD Loader sources archive and OpenCL header files from Khronos OpenCL Registry http://www.khronos.org/registry/cl/
  2. Unpack the archive and put headers in inc/CL sub-folder
  3. Print make in root of unpacked archive to compile OpenCL libraries.
  4. Create installation folder for OpenCL IDL Loader package and put there:
    1. OpenCL header files in include/CL subfolder
    2. libOpenCL.so (generated in bin subfolder of source package) in lib subfolder

Installation From Official Repositories

Debian-based distributives

All 3rd-party products required for building of OCCT could be installed from official repositories. You may install them from console using apt-get utility:

sudo apt-get install \   
tcllib tklib tcl-dev tk-dev \   
libfreetype-dev \   
libxt-dev libxmu-dev \   
libgl1-mesa-dev \   
libfreeimage-dev \   
libtbb-dev \   
libgl2ps-dev   

To launch WOK-prebuilt binaries you need install C shell and 32-bit libraries on x86_64 distributives:

sudo apt-get install \   
csh \   
libstdc++5:i386 libxt6:i386   

Any compliant C++ compiler is required for building anyway:

sudo apt-get install \   
g++